AT3-310A
Excellent performance --- The system can operate a variety of input and output options with tray, tube and tape I/O devices thus provides programming/testing, tape-out-marking and packing conversion for most of IC products on / in tray, tube and tape.Intelligent operation --- Automatic multiple pick & place operation in sequence of IC loading / pickup / positioning / insertion / programming or testing / sorting / optional marking / unloading with powerful software control.Accurate positioning --- System is equipped with two precise CCD. One fixed, upward CCD for IC positioning while the other carried, downward CCD for sockets / pick & place spots positioning.Reliable programming/testing --- The built-in programmers/testers are designed with high speed CPU, resided FPGA, high capacity pin drivers and USB interface, thus providing a high speed, low noise, accurate and reliable programming/testing platform.Multi-site programming/testing --- Programming/Testing Module may have 1, 2, 4, 6 or 8 sockets on board considering programming/testing time. Up to 8 units x 4 sets = 32 units of IC can be programmed/tested simultaneously, thus eliminating / minimizing handler idle time when programming/testing high capacity memory devices.High throughput --- Up to 2000 UPH, about 7.2 sec. handler index time for each 4 units of pick & place. System offers ~2000 units / hour consistent throughput for ICs with programming/testing time less than 43 sec.Optional marking --- System provides optional dot / alphanumeric tape-out-marking after programming/testing.Easy change-over & maintenance --- Easy and fast change-over of socket modules and I/O devices when switching IC products among tray, tube and tape. Power-on self-diagnostics, I/O devices detect/test function and module design allow system easy for maintenance, repair and replacement.Powerful operation software --- Both setup data and test results are automatically saved for next power-on operation as well as for quality / yield traceability. Graphical user interface makes it easy to access.SpecificationsMotionX-Y drive : High performance servo drive systemTransmission : Ball screw & linear guide mechanismResolution : X axis: ±0.02mm, Y axis: ±0.02mm, Z axis: ±0.02mmMax. stroke : X axis: 940mm, Y axis: 535mm, Z axis: 30 mmTheta axis resolution : 0.15°Pick & Place head placement accuracy : ±0.03mmVisionCamera : Fixed CCD: 659 x 494 pixels. Carried CCD: 659 x 494 pixelsField of view : 25mm x 25mmVision alignment : IC corner leadsVision accuracy : ±0.01mmVision process time : ~ 0.1 sec / unitProgramming/TestingResident programmer/tester : ALL-100A for programming of regular MCU and memory devicesFLASH-100 for programming of high capacity memory devicesICT-96 for testing of regular memory devicesProgramming/Testing site : 8 sites x 4 sets = 32 sitesPin driver : ALL-100A: 68 universal pin drivers per setFLASH-100: 56 x 8 universal pin drivers per setICT-96: 96 universal pin drivers per setApplicable products : PROM, EPROM, EEPROM, FLASH, MCU, PLD, PAL, FPGA... etc.Applicable packages: SOP, SSOP, PLCC, MLF, TSOP, QFP, QFN, TQFP, BGA, μBGA…etc.MarkingMarking : Optional tape-out-marking with dot (1.5mm ~ 2.0mm) or alphanumeric (2mm x 3mm)ThroughputHandler index time : ~ 7.2 sec. / 4 unitsThroughput : ~ 2000 UPHI/O devicesAuto Tray : Auto tray move in, move out and replacement. Stack up to 20~25 JEDEC trays for fresh / pass unitsSemi-auto Tray : Auto tray move in, move out but manual replacement for fresh / pass unitsManual Tray : Two JEDEC trays for manual input / output or spares / rejects binningNG Plate : One small plate for prog. & other rejectsTube Input : 150mil, 208mil, 300mil… packages available. Load capacity : 4 tubesTube Output : 150mil, 208mil, 300mil… packages available. Load capacity : 4, 6 or 8 tubesTape Input : Electrical drive mode Tape In with carrier tape retriever2 sets of Tape In can be installed in parallel for tape with 8 ~ 16mm tape widthOne set of Tape In can be installed for tape with 16 ~ 32mm tape widthTape Output : Options of heat sealing mode & pressure sealing mode are availableAccept tape with 12 ~ 32mm tape widthControlBuilt-in Controller : PC-based control with Windows XPDisplay : 19” LCD monitorData entry : Keyboard / mousePower & AirPower : Power voltage : AC 200 ~ 245V / 50-60Hz Single phase with built-in UPS.Power consumption : 1.3 KVAAir : Air pressure : 0.6 MPa (~6.0 kg/cm2). Air consumption : 45 liter/min.DimensionBase Unit W x D x H : 1500mm x 840mm x 1510mm (H: 1775mm with tower light installed)Base + Tray I/O W x D x H : 1500mm x 1400mm x 1510mmBase + Tube I/O W x D x H : 1500mm x 1620mm x 1510mmBase + Tape I/O W x D x H : 1500mm x 1840mm x 1510mmWeightBase Unit : ~ 680 kg